| CLUTCH |
|
|
|
|
|
| Make and type |
... ... ... ... ... ...
|
Ford, single dry plate |
| Operation |
... ... ... ... ... ...
|
Hydraulic with centrifugal assistance |
| Driven plate—Diameter |
... ... ... ... ... ...
|
10 in. (25.4 cm.) or 104 in. (26.4 cm.) |
|
|
... ... ... ... ... ...
|
12 (6 small, 6 large) |
—Colour of pressure springs
|
... ... ... ... ... ...
|
Orange |
| Free movement of withdrawal lever |
... ... ... ... ... ...
|
Not adjustable (see Section D) |
|
|
|
|
|
|
|
|
|
| GEARBOX (for torque loading |
figures see table at |
end of section) |
|
|
|
| Type |
... ... ... ... ... ...
|
4 speed and reverse |
| Synchromesh on |
... ... ... ... ... ...
|
All forward gears |
| Bearing type—Mainshaft |
... ... ... ... ... ...
|
Ball |
|
|
... ... ... ... ... ...
|
Needle rollers |
|
|
... ... ... ... ... ...
|
Ball |
|
|
... ... ... ... ... ...
|
Needle rollers |
|
|
... ... ... ... ... ...
|
Bush |
| Adjustment —Mainshaft |
... ... ... ... ... ...
|
Thrust washers |
| —Layshaft end float |
... ... ... ... ... ...
|
-.004/.018in.(.10/.45 mm.) |
|
|
|
|
“260”(HEH-H)
|
“289” (HEH-B)
|
|
("Close" Ratio)
|
("Wide" Ratio)
|
| Ratios—Top |
1.00 : 1
|
1.00 : 1
|
|
|
1.29 : 1
|
1.36 : 1
|
|
|
1.69 : 1
|
1.93 : 1
|
|
|
2.32 : 1
|
2.78 : 1
|
|
|
2.32 : 1
|
2.78 : 1
|
|
|
|
|
|
|
|
|
|
| PROPELLER SHAFT |
|
|
|
|
|
| Type |
... ... ... ... ... ...
|
Open shaft |
| Outside diameter |
... ... ... ... ... ...
|
2 in. (5 cm.) |
| Length between centres |
... ... ... ... ... ...
|
21.25 in. (53.97 cm.) |
| Universal joint |
... ... ... ... ... ...
|
Needle roller |
|
|
|
|
|
|
|
|
|
| REAR AXLE (for torque loading |
figures see table at |
end of section) |
|
|
|
| Type and final drive |
... ... ... ... ... ...
|
Salisbury hypoid 4.HA |
| Ratio |
... ... ... ... ... ...
|
2.88 : 1 |
| Bearings—Bevel pinion |
... ... ... ... ... ...
|
Taper roller |
|
|
... ... ... ... ... ...
|
Taper roller |
|
|
... ... ... ... ... ...
|
Taper roller |
| Adjustment—Bevel pinion |
... ... ... ... ... ...
|
Shims |
|
|
... ... ... ... ... ...
|
Shims |
—Crown wheel to pinion backlash
|
... ... ... ... ... ...
|
004 in.(.10 mm.)Minimum
(etched on drive gear) |
—Half shaft (axle shaft) end float
|
... ... ... ... ... ...
|
.006/.008 In. (.15/.20 mm.) |
| No. of teeth-Crown wheel |
... ... ... ... ... ...
|
49 |
|
|
... ... ... ... ... ...
|
17 |
**
